TM 5-3895-374-24-2 8. Place   output   hub   seal   carrier   in   position   without shims   and   install   two   carrier   screws   diametrically opposed.    Torque  each  screw  to  25  lb.-ins.    Rotate the output hub to roll in the bearings and then torque each  screw  once  to  50  Ib.-ins.    Do  not  retorque screws.        Again    turn    output    hub    to    roll    in    the bearings.  With a feeler or taper gage, measure the gap  between  the  housing  and  the  carrier,  clockwise from   and   next   to   each   screw.      To   determine   the required shim thickness, add the average of the two feeler  gage  readings  to  the  constant  given  in  Table 4.    Remove  carrier  and  install  the  required  shims. Note:   Total   shim   thickness   per   carrier   should   not include   more   than   .009"   plastic   shims   and   each plastic  shim  should  be  inserted  between  two  metal shims.  Place a 1/8" diameter bead of Dow Corning RTV732  sealant  on  the  face  around  the  I.D.    of  the end shim (sealant is to be between reducer housing and   shim)   and   install   carrier   on   reducer   housing. Torque   carrier   bolts   to   value   shown   in   Table   4. Output hub should have an axial end play of .001" to .003". 9. Adjust   the   countershaft   bearings   using   the   same method   as   in   step   8   above.      The   axial   end   play should be .001" to .003’. Table 4-Bolt Tightening Torque Values. Screw Shaft Seal Conveyor Housing Adapter Retainer Carrier Drive Bolts Bolts Bolt Bolts Size (in.-lbs.) (in.-lbs.) (in.-lbs.) (in.-lbs.) SCXT309A SCXT315A 600 900 3120 204 SCXT325A SCXT409A SCXT415A 600 1800 3120 360 SCXT425A SCXT509B SCXT515B 900 1800 3120 360 SCXT525B Table 5-Manufacturers’ Part Numbers For Replacement Output Hub Bearings. TORQUE ARM Output Hub Bearing Reducer Drive DODGE Timken Size Part Number Part Number SCXT309A SCXT315A 402272 LM814849 SCXT325A 403127 LM814810 SCXT409A SCXT415A 402268 498 SCXT425A 403163 492A SCXT509B SCXT515B 402193 42381 SCXT525B 403016 42584 10.  Again using the same procedure as in step 8, adjust the  input  shaft  bearings,  except  the  axial  end  play should be .002" to .003’. 11.  Apply  a  sealant  to  the  input  shaft  cover  gasket  and install  input  shaft  cover  in  right-hand  housing  half. Install input and output  seals.    Extreme  care  should be  used  when  installing  seals  to  avoid  damage  due to contact with any sharp edges on the input shaft or output  hub.    Possibility  of  damage  and  consequent oil  leakage  can  be  decreased  by  covering  all  sharp edges  with  tape  or  paper  prior  to  seal  installation. Fill   cavity   between   seal   lips   with   grease.      Seals should  be  pressed  or  tapped  with  a  soft  hammer evenly into place in the carrier applying pressure only on the outer edge of the seals.  A slight oil leakage at the seals may be evident during initial running in but should disappear unless seals have been damaged. 12.  Reassemble and install the Screw Conveyor Drive in accordance  with  the  instruction  in  the  front  of  this manual. Table 6-Manufacturers’ Part Numbers For Replacement Countershaft Bearings. TORQUE-ARM Countershaft Bearing Countershaft Bearing Reducer Input Side Adapter Side DODGE Timken DODGE Timken Size Part No. Part No. Part No. Part No. SCXT309A SCXT315A 402273 15102 402273 15102 SCXT325A 403094 15245 403094 15245 SCXT325A SCXT409A 402000 M86649 402000 M86649 SCXT425A 403000 M86610 403000 M86610 SCXT509B SCXT515B 402203 2789 402203 2789 SCXT525B 403027 2720 403027 2720 Table 7-Manufacturers’ Part Numbers For Replacement Input Shaft Bearings. TORQUE-ARM Countershaft Bearing Countershaft Bearing Reducer Input Side Adapter Side DODGE Timken DODGE Timken Size Part No. Part No. Part No. Part No. SCXT309A 402204 LM48548A 402273 15102 SCXT315A 403139 LM48510 403094 15245 SCXT325A SCXT409A 402280 2788 402142 26118 SCXT415A 403027 2720 403102 26283 SCXT425A SCXT509B 402144 28579 402269 350 SCXT515B 403104 28521 403073 352 402144 28579 402266 350A SCXT525B 403104 28521 403073 352 page 3-795