• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
Screw Conveyor Motor Mounts
Replacement Parts for TA1 M thru TA7M Motor Mounts

TM-5-3895-374-24-2 M081 Asphalt Mixing Plant Manual
Page Navigation
  181    182    183    184    185  186  187    188    189    190    191  
TM 5-3895-374-24-2 INSTALLATION MANUAL TA1M thru TA7M Motor Mounts for DODGE’ Torque-Arm Speed Reducers (Sizes TXT1 thru TXT7) INSTALLATION Note Refer   to   photo   for   position   of   all   parts before installation. 1. Remove  the  two  or  three  bolts  required  for  mounting  the TAM  Motor  Mount  from  the  reducer  housing.    Install  the front and rear supports (2) using the new reducer bolts (1 ) supplied with the motor mount.  Make sure support flanges face output side of reducer.  Tighten bolts securely. 2. Mount  bottom  plate  (3)  on  supports  with  bolts  supplied. Insert   bolts   (7)   from   top   through   slotted   holes.      Add flatwasher, lockwasher, and nut.  Hand tighten. 3. Thread   two   nuts   (6)   on   each   threaded   stud   (5)   leaving approximately   1"   of   stud   protruding   at   one   end.      Insert threaded  stud  with  1"  of  threads  through  corner  holes  of bottom plate, thread a hex nut (6) on the stud and tighten securely. 4. Slide  top  plate  (4)  over  the  threaded  stud,  making  sure center  handling  hole  is  positioned  opposite  input  side  of reducer.    Thread  a  hex  nut  (6)  on  the  studs  and  tighten securely. 5. Locate  the  proper  position  for  the  motor  and  bolt  it  to  the top plate.  Tighten bolts securely. WARNING If electrical connections to motor are Installed at  this  time,  disconnect  and  lock  out  power supply before proceeding. 6. Install motor sheave and reducer sheave as close to motor and  reducer  housings  as  possible.    Accurately  align  the motor   and   reducer   sheave   by   sliding   bottom   plate   in relation to supports.  Tighten bolts (7) securely. 7. Install   V-belts   and   tension   belts   by   alternately   adjusting nuts (6) on the threaded studs (jackscrews).  Make certain that   all   bolts   are   securely   tightened,   the   V-belt   drive   is properly   aligned   and   the   belt   guard   is   installed   before operating the drive. MOUNT MOTOR AT ANY POINT AROUND DRIVE SHAFT WARNING: Because of the possible danger to person(s) or property from accidents which may result from the improper use of products.  it is important that correct procedures be followed: Products must be used in accordance with the engineering information specified in the catalog.  Proper installation, maintenance and operation procedures must be observed.  The instructions in the instruction manuals must be followed.  Inspections should be made as necessary to assure sale operation under the prevailing conditions. Proper guards and other suitable safety devices or procedures as may be desirable or as may be specified in safety codes should be provided.  and are neither provided by Reliance Electric Industrial Company nor are the responsibility of Reliance Electric Industrial Company.  This unit and its associated equipment must be installed, adjusted and maintained by qualified personnel who are familiar with the construction and operation of all equipment in the system and the potential hazards involved.  When risk to persons or property may be involved.  a failsafe device must be an integral part of the driven equipment beyond the speed reducer output shaft. DODGE / P.O.  Box 499 / 2 Ponders Court / Greenville, South Carolina 29602-0499 / 803-297-4800 © Reliance Electric Company.  1990  DODGE is a registered trademark of Reliance Electric Company or its affiliates. Printed in U.S.A. Instruction Manual 499369 1/89 8M-K page 3-855







Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.